electrical parameters @ 25 c ? isolation : 1500 vrms ? impedance : 100 w ? rise time : 3.0 ns max. insertion loss (db max.) common mode rejection (db min.) crosstalk (db min.) return loss (db min.) 1-80 mhz 30-100 mhz 200 mhz 300 mhz 1-80 mhz 100 mhz 150 mhz 1-30 mhz 60 mhz 100 mhz xmit rcv xmit rcv xmit rcv xmit rcv xmit rcv xmit rcv xmit rcv xmit rcv xmit rcv ocl @ 70 c 100 khz, 0.1 vrms 8 ma dc bias 350 m h media side -1 -1 -18 -3 -18 -10 -30 -36 -25 -20 -1 -1 -18 -3 -18 -10 -25 -20 -10 10/100 base-x module for ics 1890 & ssi 78q2120 multi-port applications ? also recommended for broadcom bcm5208 10/100 solution ? ? significantly improved common mode attenuation ? ? guaranteed to operate with 8 ma dc bias at 70 c ? ? complies with or exceeds ieee 802.3, 10 bt/100 bx standards ? EPF8058S dimensions package schematic e l e c t r o n i c s i n c . csf8058sa rev. 1 3/20/97 receive channel media side 1:1 39, 31, 29, 21 40, 32, 30, 22 chip side 2, 7, 12, 17 1, 6, 11, 16 transmit channel 36, 33, 26, 23 38, 35, 28, 25 37, 34, 27, 24 1ct:1ct 5, 10, 15, 20 4, 9, 14, 19 3, 8, 13, 18 media side chip side a b c d e f g h i j k l m n p q dim. 1.110 .470 .235 .950 .008 .050 .620 .016 .008 .085 0 .045 min. 1.130 .490 .255 typ. .012 typ. .640 .022 .012 typ. 8 typ. max. .030 .050 .090 .670 nom. (inches) (millimeters) 28.19 11.94 5.97 24.13 .203 1.27 15.75 .406 .203 2.16 0 1.14 min. 28.70 12.45 6.48 typ. .305 typ. 16.26 .559 .305 typ. 8 typ. max. .762 1.27 2.29 17.02 nom. f solder pad layout pca EPF8058S date code b q n m p 120 21 40 c l i g e d h a k j tel: (818) 892-0761 fax: (818) 894-5791 http://www.pca.com pca electronics, inc. 16799 schoenborn st. north hills, ca 91343 xmit rcv -15 --- 500 mhz product performance is limited to specified parameters. data is subject to change without prior notice.
csf8058sb rev. 1 3/20/97 10/100 base-x module for ics 1890 & ssi 78q2120 multi-port applications EPF8058S e l e c t r o n i c s i n c . the circuit below is a guideline for interconnecting pcas EPF8058S with ics 1890 chip for 10/100 mb/s applications. further details can be obtained from the chip manufacturer application notes. connection to the alternative chip ssi 78q2120 is straight forward; please consult the ssi data sheet recommendations for completing this project. typical insertion loss of the isolation transformer is 0.5db. this parameter covers the entire spectrum of the encoded signals in 10/100 protocols. under terminated conditions, to transmit a 2v pk-pk signal across the cable, you must adjust the chips supporting resistor to get at least 2.12v pk-pk across the transmit pins. primary side center tap can be returned to the chip side ground plane; but more often than not, if the ground plane is itself noisy, field experience has shown that it may worsen emi situation. it is perhaps wiser to carefully lay the system board so that substantial gain in emi suppression is obtained from the so called common mode termination on the cable side as shown below. in any event, this configuration has been known to be quite successful in the field in emi containment for similar applications. the phantom resistors shown around the connector have been known to suppress unwanted radiation that unused wires pick up from the immediate environment. their placement and use are to be considered carefully before a design is finalized. it is recommended that there be a neat separation of ground planes in the layout. it is generally accepted practice to limit the plane off at least 0.05 inches away from the chip side pins of EPF8058S. there need not be any ground plane beyond this plane. for best results, pcb designer should design the outgoing traces preferably to be 50 w , balanced and well coupled to achieve minimum radiation from these traces. typical application circuit for utp (only one port shown) notes : only one port shown for hub side connection. ics 1890 rj45* 1 2 6 3 4 5 7 8 tx+ tx- rx+ rx- chassis ground 50 w 50 w 75 w EPF8058S 55 w high voltage capacitor 55 w 50 w 50 w cm capacitor 5vcc 3 5 1 2 40 36 37 39 38 rcv xmit tel: (818) 892-0761 fax: (818) 894-5791 http://www.pca.com pca electronics, inc. 16799 schoenborn st. north hills, ca 91343
|
